Double-head bending
MOTI-600B Double-head Busbar Bending Machine
For busduct connection bars and end forming.
The 600B is a double-head bending machine for busduct connection bars. Its working range is 3 × 30 to 6 × 200 mm. Review both end shapes, their spacing and assembly references before selecting the dies.
Thickness × width
3 × 30 to 6 × 200 mm
Send your drawing to check material, tooling and operation limits.
THE RIGHT APPLICATION
Dedicated double-head forming for busbar trunking connections.
The MOTI-600B addresses connection bars used in busduct and busbar trunking systems. Instead of offering a general cutting, punching and bending workstation, it uses two hydraulic bending heads for forming corresponding ends of a connection. The published range runs from 3 × 30 mm to 6 × 200 mm. It is most useful to evaluate with a complete two-ended connection drawing, including the spacing and relationship between the ends.
01 TECHNICAL OVERVIEW
Know the working range.
Compare these working limits with your part. Your quotation identifies the supplied machine version and tooling.
| Thickness × width | 3 × 30 to 6 × 200 mm |
|---|---|
| Machine weight | 1300 kg |
| Motor power | 4 kW |
| Machine dimensions (L × W × H) | 3600 × 1000 × 1500 mm |
| Bending force | 60 Ton |
| Control | Manual |
Before you choose
The headline capacity is an initial selection reference. Hole size, edge distance, bend direction and tooling can impose separate limits. Request a drawing review for your application. This is a bending machine, not a three-process workstation.
Keep both connection ends in the same review
The double-head arrangement forms the connection-bar ends without turning the bar between end operations. Submit the complete drawing, including both offsets, overall length and assembly datums, so the matched tools can be reviewed.
02 INSIDE THE PROCESS
See how the work gets done.
Equipment details, positioning and the workpiece requirements to discuss for this model.
01
Form both ends in one setup
The product describes forming two bends at each end using the double-head arrangement. The tool design defines the finished offset. Review both ends together: a correct individual bend is insufficient if the relative end positions do not match the assembly.
02
Check the connection geometry
Provide thickness, width, total finished length, offsets, angles and internal radii. Show the mating assembly or connection detail when that controls fit. For unusually short parts or conflicting bend directions, a drawing review is needed before a tooling proposal.
03
Manual operation with hydraulic forming
The two bending heads use manual control with hydraulic forming. Include workpiece placement, removal and dimensional inspection when reviewing the operation.
03 TOOLS & FINISHED PARTS
Tooling, configuration and options
Quoted forming tools: Specify both connection-bar ends, their offsets and the relationship between them. The matched double-end tools are defined for the complete drawing.
Configuration review: Agree on the required part-length range and tool setup. Cutting and punching are separate upstream operations.
Matched forming tools
Specify both end shapes and their relationship, with a drawing revision for the sample.
Location and adjustment
Confirm the supported part-length range and setup method for the proposed connection.
Dedicated application
The 600B is a bending machine. Plan upstream cutting and punching separately.
FOR A TOOLING REVIEW
Send the complete connection.
- Material and thickness × width
- Hole sizes, centers and edge distances
- Bend direction, radius, angle and flange length
- Assembly references and tolerances
- Machine model and tooling interface
04 FROM SELECTION TO PRODUCTION
Review a complete working cycle.
Submit the whole connection
A cropped view of one end is not enough to specify a double-head arrangement. Include the complete length and the assembly datums.
Agree on a representative trial
Inspect the offset and relative position of both ends after forming. Use the material and thickness intended for production.
Plan the production cell
The published machine measures 3,600 × 1,000 × 1,500 mm and weighs 1,300 kg. Allow working space around both ends and include the preceding cutting and punching operations in the layout.
05 MOTI-600B · QUESTIONS
Before you choose.
No. The 600B is a double-head bending machine for busduct connection bars. Cutting and punching are separate operations in the production flow.
The 600B is focused on paired end forms for busduct connections. A changing mix of complex busbar shapes may require a different bending process and tool arrangement.
The published thickness range is 3–6 mm, paired with widths from 30–200 mm. Have the complete size and shape combination reviewed for the proposed tools.
06 COMPARE OPTIONS
Find the right level of capability.
Servo CNC bending center
Dedicated bending with a 160 mm width.
15 × 160 mm
Thickness × width · operation limits apply
Servo CNC bending center
Dedicated bending with a 200 mm width.
15 × 200 mm
Thickness × width · operation limits apply
3-in-1 workstation
A wider working range for panel production.
16 mm thickness class
Thickness × width · operation limits apply
Tell us about the busbars you make.
Share your material, maximum thickness and width, and the cutting, punching or bending work you need. A drawing or a sample requirement helps us discuss the right machine and tooling.
We use your details to respond to your machine enquiry. For drawings, use the email or WhatsApp links below.
Have a drawing? Attach your PDF, CAD file or clear part photo in email or WhatsApp. Include material, thickness, width and quantity.